Why Understanding Plumbing Basics is Essential When Installing a Bathtub
Why Understanding Plumbing Basics is Essential When Installing a Bathtub
Blog Article
We have found this post relating to How to Install a Bathtub listed below on the internet and figured it made perfect sense to relate it with you on my blog.
Mounting a bath tub isn't exactly rocket science, but it does require solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bathtub with a brand-new one is also a reasonably hard task. If the old bathtub is conveniently easily accessible, the job can relocate rapidly; if you need to open up a wall to eliminate the old bathtub and also position the new tub, the task is a lot harder. In either case, the job is within a home handyman's abilities, although you will certainly need an assistant to leave the old tub and also embeded in the new one. Ensure you have certified yourself for the work as well as are comfortable trying it. Rather than working with a specialist to take control of a halfway-completed project, it is much better to consider utilizing one before you begin. Possibilities are you might require a specialist plumber to make tube connections.
This short article will certainly assist you install a brand-new tub in your washroom if you have already gotten a new bathtub as well as do not need to change the plan of your previous supply of water pipelines.
Your tools as well as material list need to consist of the following:
Preparing for the Installation
First of all, the sustaining frame supplied with the bath should be fitted (if needed) according to the supplier's guidelines. Next, fit the taps or mixer to the tub. When suitable the tap block, it is important to ensure that if the faucet features a plastic washer, it is fitted between the bath and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps unit to stop pressure on the bath tub.
Fit the adaptable tap connectors to the bottom of both faucets making use of 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. See to it you use every one of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be suited its final setting.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the water system. After doing so, turn on the faucets to drain pipes any type of water staying in the system. The procedure of removing the existing taps can be fairly problematic due to the restricted accessibility that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a fabric prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been removed, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. When the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing substance.
Before proceeding to fit the brand-new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Utilizing the two wood boards under its feet, put the tub in the required setting. The wood boards are practical in equally spreading the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto 4 little factors.
The following objective is to ensure that the bathtub is leveled all round. This can be attained by checking the level and also readjusting the feet on the tub until the spirit level reviews degree.
To install faucets, fit all-time low of the outermost adaptable tap adapter to the proper supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Turn on the supply of water and also inspect all joints as well as brand-new pipework for leaks and also tighten them if required. Load the bathtub as well as additionally inspect the overflow electrical outlet as well as the regular outlet for leakages.
Finally, repair the bathroom paneling as defined in the supplier's instruction manual. Tiling as well as securing around the bathtub ought to wait up until the bath tub has actually been made use of at least once as this will settle it into its last setting.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the faucet and the other end offers a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin ensuring that the washing machines are in place in between the tap and the sink. Protect the tap in position with the producer offered backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former kind should be linked to the faucet ends first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom meets the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack an inflexible seal, causing the water to penetrate the wall surface between the bathroom and also the tiling, resulting in complications with moisture and possible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your components as well as fittings. They are sold in tubes and cartridges, and also can sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of drenched newspaper or soft rope. Remember to always fill the bathtub with water prior to sealing, to allow for the motion experienced when the bathtub remains in use. The sealer can break rather early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is a good idea to fit the tiles utilizing waterproof or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
I came across that content about Tools You Need to Install a New Bathtub when browsing on the internet. So long as you enjoyed reading our blog entry please be sure to pass it around. I praise you for your time. Visit us again soon.
Address emergency plumbing promptly here. Report this page